The Virtual Navy

GO TO TEST

Tank Officer: Commanding a tank platoon offers fast-paced excitement and heavy firepower, and it requires an agile mind coupled with an iron will. As a tank officer, you'll lead a platoon of 15 Marines and four M1A1 tanks through every possible scenario imaginable.

You will be placed with a marine tank battalion to operate one of the most deadliest tanks in the world.  Your job is simple kill or be killed!  All of your training will be done in game utalizing the M1A1 thru obssticals and against enemy armor, and other assets.  You will also need to qualify in the use of the M-9, and M-16 at the weapons range.

M1A1 Abrams

The M1 Abrams is a main battle tank produced in the United States. The M1 is named after General Creighton Abrams, former Army Chief of Staff and former commander of the 37th Armored Regiment. It is a well armed, heavily armored, and highly mobile tank designed for modern armored ground warfare.Notable features of the M1 Abrams include the use of a powerful gas turbine engine, the adoption of sophisticated composite armor, and separate ammunition storage in a blow-out compartment for crew safety. It is one of the heaviest tanks in service, weighing in at close to 70 tons.

The M1 Abrams entered U.S. service in 1980, replacing the M60 Patton and M48A5. It did, however, serve for over a decade alongside the improved M60A3, which had entered service in 1978. Three main versions of the M1 Abrams have been deployed, the M1, M1A1, and M1A2, incorporating improved armament, protection and electronics. These improvements, as well as periodic upgrades to older tanks have allowed this long-serving vehicle to remain in front-line service. It is the principal combat tank of the United States Army and Marine Corps.

The Abrams is protected by Chobham armor, a further development of British "Burlington" armor. Chobham is a composite armor formed by spacing multiple layers of various alloys of steel, ceramics, plastic composites, and kevlar, giving an estimated maximum (frontal turret) 1320-1620 millimeters of RHAe versus HEAT (and other chemical energy rounds) and 940-960 mm versus kinetic energy penetrators. It may also be fitted with reactive armor over the track skirts if needed (as in the Urban Survival Kit) and Slat armor over the rear of the tank and rear fuel cells to protect against ATGMs. Fuel and ammunition are in armored compartments with blowout panels to protect the crew from the risk of the tank's own ammunition cooking off if the tank is damaged. Protection against spalling is provided by a kevlar liner. Beginning in 1987, M1A1 tanks received improved armor packages that incorporated depleted uranium (DU) mesh in their armor at the front of the turret and the front of the hull. Armor reinforced in this manner offers significantly increased resistance towards all types of anti-tank weaponry, but at the expense of adding considerable weight to the tank.

The first M1A1 tanks to receive this upgrade were tanks stationed in Germany, since they were the first line of defense against the Soviet Union. US-based tank battalions participating in Operation Desert Storm received an emergency program to upgrade their tanks with depleted uranium armor immediately before the onset of the campaign. M1A2 tanks uniformly incorporate depleted uranium armor, and all M1A1 tanks in active service have been upgraded to this standard as well, the armor thickness is believed to be equivalent to 24 inches (610 mm) of RHA. The strength of the armor is estimated to be about the same as similar western, contemporary main battle tanks such as the Leopard 2. The M1A1/M1A2 can survive multiple hits from the most powerful tank munitions (including 120 mm depleted uranium APFSDS) and anti-tank missiles. In the Persian Gulf War, Abrams tanks survived multiple hits at relatively close ranges from Iraqi T-72s and ATGMs. M829A1 "Silver Bullet" APFSDS rounds from other M1A1 Abrams were unable to penetrate the front and side armor (even at close ranges) in friendly fire incidents as well as an incident in which another Abrams tried to destroy an Abrams that got stuck in mud and had to be abandoned.

In addition to the advanced armor, some Abrams, are equipped with a Missile Countermeasure Device that can impede the function of guidance systems of semiactive control line-of-sight (SACLOS) wire and radio guided anti-tank guided missiles (Russian AT-3, AT-4, AT-5, AT-6 and the like) and thermally and infrared guided missiles. (ATGM). This device is mounted on the turret roof in front of the Loader's hatch, and can lead some people to mistake Abrams fitted with these devices for the M1A2 version, since the Commander's Independent Thermal Viewer on the latter is mounted in the same place, though the MCD is box-shaped and fixed in place as opposed to cylindrical and rotating like the CITV.

In the chance that the Abrams does suffer damage resulting in a fire in the crew compartment, the tank is equipped with a halon fire-suppression system that automatically engages and extinguishes fires in seconds.

Main armament

M68A1 rifled gun

The main armament of the original model M1 was the M68A1 105 mm rifled tank gun firing a variety of high explosive anti-tank (HEAT), high explosive, white phosphorus, and a highly efficient and lethal anti-personnel (multiple flechette) round. This gun is a license-built version of the British Royal Ordnance L7 gun. While being a reliable weapon and widely used by both NATO and former Warsaw Pact nations alike, a cannon with lethality beyond the 3 kilometer range was needed to combat newer armor technologies. To attain that lethality, projectile diameter needed to be increased. The M68A1's performance in terms of accuracy and armor-piercing penetration is on par with the M256A1 up to 3000 meters out, but beyond that range the 105mm projectile lacks the kinetic energy to defeat modern armor packages.

M256 smoothbore gun

The main armament of the M1A1 and M1A2 is the M256A1 120 mm smoothbore gun, designed by Rheinmetall AG of Germany. The M256A1 is a variant of the Rheinmetall 120 mm L/44 gun carried on the German Leopard 2 on all variants up to the Leopard 2A5. Leopard 2A6 replaced the L/44 barrel with a longer L/55. The newer M256A1 is manufactured under license in the United States by Watervliet Arsenal, New York.

The M256A1 fires a variety of rounds. The M829A2 was developed specifically to address the threats posed by a Soviet T-90 or T-80U tank equipped with kontakt-5 Explosive Reactive Armor. It also fires HEAT shaped charge rounds such as the M830, the latest version of which (M830A1) incorporates a sophisticated multi-mode electronic sensing fuse and more fragmentation which allows it to be used effectively against armored vehicles, personnel, and low-flying aircraft. Unlike the Soviet-built tanks it was designed to go up against, the Abrams uses a manual loader rather than an automatic device, due to the belief that having a person reload the gun is faster and more reliable. This decision was proven out as the Soviet-era automatic loading system proved troublesome. Also important in the decision to use a crew member instead of an automatic loader during the XM-1 development was the fact that autoloaders of the day did not allow for separate ammunition storage in the turret. 

The new M1028 120 mm anti-personnel canister cartridge was brought into service early for use in the aftermath of the 2003 invasion of Iraq. It contains 1,098 3/8 inch steel ball projectiles which spread from the muzzle to produce a shotgun effect lethal out to 600 m. The steel balls can be used to clear enemy dismounts, break up hasty ambush sites in urban areas, clear defiles, stop infantry attacks and counter-attacks and support friendly infantry assaults by providing covering fire. The Canister round is also a highly effective breaching round and can level cinder block walls and knock man-sized holes in reinforced concrete walls for infantry raids at distances up to 75 meters.

In addition to this, the new XM1111 (Mid-Range-Munition Kinetic Energy) is also in development. Essentially a cannon-fired guided round, it has a range of roughly 12 km and uses a KE warhead which is rocket assisted in its final phase of flight. This is intended to be the best penetrator yet, an improvement over the US 3rd generation DU penetrator (estimated penetration 790 mm).

Secondary Armor

The Abrams tank has three machine guns:

1. A .50 cal. (12.7 mm) M2 machine gun in front of the commander's hatch. On the M1, M1IP and M1A1, this gun is on a powered mount and can be fired using a 3× magnification sight, known as the Commander's Weapon Station (CWS for short), while the vehicle is "buttoned up" with all its hatches closed to protect the crew. On the M1A2 & M1A2SEP, this gun is on a flex mount (seen at right), the Commander having to expose himself to fire the weapon manually. With the forthcoming TUSK addon kit, an M2 or an Mk 19 grenade launcher can be mounted on the CROWS remote weapons platform (similar to the Protector M151 remote weapon station used on the Stryker family of vehicles).
2. A 7.62 mm M240 machine gun in front of the loader's hatch on a skate mount. Some of these have been fitted with gun shields during the ongoing conflict in Iraq as seen in the image at right, as well as night-vision scopes for low-visibility engagements.
3. A second 7.62 mm M240 machine gun in a coaxial mount. The coaxial MG is aimed and fired with the same computer fire control system used for the main gun.

The turret is fitted with two six-barreled smoke grenade launchers (USMC M1A1s use an eight-barreled version). These can create a thick smoke that blocks both vision and thermal imaging, and can also be armed with chaff. The engine is also equipped with a smoke generator that is triggered by the driver. The Abrams also has provisions for storing an M16 rifle or M4 carbine inside the turret in case the crew is required to leave the tank under potentially hostile conditions; while the crewmen are supplied with the M9 Beretta pistol as a personal sidearm.

Aiming

The Abrams is equipped with a ballistic fire-control computer that uses data from a variety of sources, including the thermal or daylight Gunner's Primary Sight (GPS), all computing and displaying one of three components of the ballistic solution - lead angle, ammunition type, and range to the target. These three components are determined using a laser rangefinder, crosswind sensor, a pendulum static cant sensor, data on the ammunition type, tank-specific boresight alignment data, ammunition temperature, air temperature, barometric pressure, a muzzle reference sensor (MRS) that determines and compensates for barrel droop at the muzzle due to gravitational pull and barrel heating due to firing or sunlight, and target speed determined by tracking rate tachometers in the Gunner's or Commander's Controls Handles allowing for target speed input into the ballistic solution.

The fire-control system uses this data to compute a firing solution for the gunner. The ballistic solution generated ensures a hit percentage greater than 95 percent at nominal ranges. Either the commander or gunner can fire the main gun. Additionally, the Commander's Independent Thermal Viewer (CITV) on the M1A2 can be used to locate targets and pass them on for the gunner to engage while the commander scans for new targets. In the event of a malfunction or damage to the primary sight system, the main and coaxial weapons can be manually aimed using a telescopic scope boresighted to the main gun known as the Gunner's Auxiliary Sight (GAS). The GAS has two interchangeable reticles; one for HEAT and MPAT (MultiPurpose AntiTank) rounds and one for APFSDS and STAFF (Smart Target-Activated Fire and Forget) ammunition. Turret traverse and main gun elevation can be accomplished with manual handles and cranks in the event of a Fire Control System or Hydraulic System failure. The commander's M2 .50 caliber machine gun on the M1 and M1A1 is aimed by a 3x magnification sight incorporated into the Commander's Weapon Station (CWS), while the M1A2 uses either the machine gun's own iron sights, or a remote aiming system such as the CROWS system when used as part of the TUSK (Tank Urban Survival Kit). The loader's M240 machine gun is aimed either with the built-in iron sights or with a thermal scope mounted on the machine gun.

Mobility

The M1 Abrams is powered by a 1500 hp (1119 kW) Honeywell AGT1500 (originally made by Lycoming) gas turbine, and a six speed (four forward, two reverse) Allison X-1100-3B Hydro-Kinetic Automatic transmission, giving it a governed top speed of 45 mph (72 km/h) on paved roads, and 30 mph (48 km/h) cross-country. With the engine governor removed, speeds of around 60 mph (100 km/h) are possible on an improved surface; however, damage to the drive train (especially to the tracks) and an increased risk of injuries to the crew can occur at speeds above 45 mph (72 km/h). The tank can be fueled with diesel fuel, kerosene, any grade of motor gasoline, JP-4 jet fuel, or JP-8 jet fuel; the US Army uses JP-8 jet fuel in order to simplify logistics. The Royal Australian Armoured Corps' M1A1 AIM SA uses diesel fuel; it is cheaper and makes practical sense for Australian military logistics.

The gas turbine propulsion system has proven quite reliable in practice and combat, but its high fuel consumption is a serious logistic issue (starting up the turbine alone consumes nearly 11 gallons of fuel). The high speed, high temperature jet blast emitted from the rear of M1 Abrams tanks makes it difficult for the infantry to proceed shadowing the tank in urban combat. The turbine is very quiet when compared to diesel engines of similar power output and produces a significantly different sound from a contemporary diesel tank engine, reducing the audible distance of the sound, thus earning the Abrams the nickname, "whispering death" during its first REFORGER exercise. Future US tanks may return to reciprocating engines for propulsion, as 4-stroke diesel engines have proven quite successful in other modern heavy tanks, e.g. the Leopard 2, Challenger 2 and Merkava. The small size, simplicity, power-to-weight ratio, and easy removal/replacement of the turbine powerpack does, however, present significant advantages over any proposed reciprocating replacement.

The Abrams can be carried by a C-5 Galaxy or a C-17 Globemaster III. The limited capacity (two combat-ready in a C-5, one combat-ready tank in a C-17) caused serious logistical problems when deploying the tanks for the First Gulf War, though there was enough time for 1,848 tanks to be transported by ship.

Specifications of variants

Note: All of the above produce a power of 1500 hp (1119 kW).

M1A1 Camoflauge

Unlike older US military vehicles from World War II through Vietnam, which used a scheme of dark brownish OD with large white stars, prototypes and early production M1 (105mm gun) & M-1IP models used the flat medium green paint known as "olive drab." Some units painted their M1s with the older MERDC paint scheme but the turn-in requirements for these tanks required repainting them to solid green. Therefore, even though a large number of the base model M1s were camouflaged in the field, few or none exist today.

M1A1s (120mm gun) came from the factory with the NATO 3 color camouflage Black/Med-Green/Dark-Brown CARC paint jobs. Today M1A1s are given the NATO three color paint job during rebuilds. M1s and M1A1s in Desert Storm were hastily painted desert tan for the 1991 Gulf war. Some, but not all, of these tanks were re-painted to their "authorized" paint scheme. M1A2s built for Middle East countries were painted in desert tan.

Some M1 series tanks are being painted desert tan for service in Iraq and some are not. Replacement parts (roadwheels, armor skirt panels, drive sprockets, etc.) are painted overall green, which can sometimes lead to vehicles with a patchwork of green and desert tan parts.

GO TO TEST

CONTACT INSTRUCTOR